Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI (LS1) System Hardware & Instrukcja Użytkownika Strona 8
- Strona / 122
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
BigStuff3 Pro SEFI System (LS1)
Version 1.0 7
Harness
Label
Wire
Color/Connector
Type
Label
Definition
Connect To Further Details
Calport
Black 3-way
Packard connector
with a purple seal
The
calibration
port that
allows the
ECU to
interface with
an external
computer
Connect one end
of the RS-232
communications
cable (supplied)
to the ECU and
the other end to
the serial port of
an external
computer.
The CalPort allows for
communication between
the BigStuff ECU and an
external Personal
Computer (PC) running
the BigComm software.
Click CalPort for further
information.
2-Step
Single yellow wire
2-Step trigger
function
Clutch or trans
brake switch
Two_Step_Trigger
Tach
Single green Wire
Tachometer
Connects to
vehicle
tachometer
Tach
HS GM FP
Single lead Packard
connector with a
single red and white
striped wire.
High Side
drive
Connect to the
positive side of
the fuel pump
relay.
Do not connect this wire
directly to the fuel pump.
A relay must be used.
Fuel_Pump
LS FP
Single lead Packard
connector with a
single black wire.
Low Side
drive Ford
Connect to the
negative side of
the fuel pump
relay.
Do not connect this wire
directly to the fuel pump.
A relay must be used.
Fan
Single lead Packard
connector with a
single red wire.
Engine
cooling fan
connection
Connect to the
negative side of a
cooling fan relay.
Do not connect this wire
directly to the fan or
positive side of the relay.
A relay must be used.
Fan
LS1 Crank
Black 3-way
Packard connector
with a purple seal
LS1 Crank
shaft
connection
Connect to stock
LS1 crank shaft
sensor located by
starter motor
LS1_Crank_Sensor
+12V Switch
Single pink wire
Switched 12V
supply input
Connect to a 12V
source that is
“live” when the
ignition key is in
the “crank”
position
See paragraph below
titled “Ignition
Connection” for further
relevant information.
Switched_Ignition
Battery (4
connections)
Four (4) 3/8” ring
terminals. Two (2)
red wire terminals
and two (2) black
wire terminals.
Positive and
Negative
Battery
Connections
The vehicle
battery only!
See paragraph below
titled “Battery
Connections” for further
relevant information.
Battery_Connections
- BigComm Software 1
- User Instruction Manual 1
- Table of Contents 2
- Table of Contents Continued 3
- 1. Introduction 3
- 3. Package Contents 6
- Firewall grommet 7
- LS1 In-line, 1-by-4, IAC 14
- Connector Pin-out 14
- IAC Coils 14
- Late Model 2-by-2 IAC 14
- Pin-Out 15
- WBO2 & 16
- Coil V-Batt 16
- 30 Amp fuse 16
- WBO2 & Coil V-Batt Relay 16
- 7. ECU Installation 19
- 8. BigComm Software Overview 19
- BigComm software CD ROM 20
- BigComm 24
- 11. Using the Tool Bar 25
- BigComm desktop icon 26
- 13. BigComm Main Menu Screen 30
- 15. Closing Windows 30
- 16. Configuration 31
- 17. Hardware Configuration 31
- For setup detail go to 33
- Coil-on-Plug (COP) 33
- Crank_Reference_Setup 33
- TPS Signal in the Dash 34
- 19. Dwell Time Table 38
- 20. Load vs. RPM 40
- 21. Firing Order 44
- 22. Injector Opening Time 44
- 23. Injector Phase Angle 45
- 25. Air Fuel Ratio Table 48
- 26. Positive 02 Correction 52
- 27. Negative 02 Correction 53
- 30. SPARK (F4 – “Quick Key”) 56
- 31. Spark Table 57
- 32. FUEL (F3 – “Quick Key”) 60
- 33. Fuel Table 61
- 34. STARTING 64
- 36. After Start Delay 66
- 37. After Start Correction 67
- 38. After Start Decay 68
- 39. Idle 69
- 40. Throttle Follower 70
- 41. Desired Idle RPM 71
- 42. Idle Spark 71
- 43. IAC Start Position 72
- 44. IAC Gain Terms 73
- 45. Warm Up 74
- 48. TRANSIENT FUEL 76
- 51. MAP AE Decay Rate 79
- 52. MAP AE Inc Rate 80
- 53. Run Time Correction 81
- 54. dMAP Parameters 82
- 55. dTPSdt 84
- 56. AE Position Correction 85
- 57. Individual Cylinder 86
- 60. Boost 88
- 61. Boost Parameters 89
- 62. Boost PWM 90
- 63. Boost Staged 91
- 65. Learning 94
- 67. Learning Display Table 95
- 68. Dash 96
- 69. Configure Dash 96
- 70. Save a Dash 99
- 71. Load From File 101
- 72. Save to File 102
- 73. Logging (External) 104
- 74. Configure Log 105
- 76. View Log from File 106
- Red cursor 109
- 79. Configure Replay 111
- 80. Upload 112
- 81. View Replay From File 113
- Blue Ellipse represents the 116
- 85. Load Calibration 118
- To set up, go to Gear_Box 120
- To set up, go to Gears 120
- 87. Acronym Definition 121
- 88. Control Keys 121
- 89. Function or “Quick Keys” 121
- 90. Definitions 121
- 91. ECU Pin-out 122
Powiązane produkty i podręczniki dla Do samochodu Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI (LS1) System Hardware &
Do samochodu Precision-turbo-and-engine NLR AMS-500 Boost Controller Instrukcja Użytkownika
(8 strony)
(8 strony)
Do samochodu Precision-turbo-and-engine NLR AMS-1000 Boost Controller Instrukcja Użytkownika
(25 strony)
(25 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji