Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI System Hardware & BigC Instrukcja Użytkownika Strona 73
- Strona / 138
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
BigStuff3 Pro SEFI System
Version 2.1 – February 2011 66
The Main Tool Bar can also be used to access the “Fuel” table. From the Main BigComm software
screen tool bar left click on Fuel and the drop down screen will open.
Using the PC’s mouse, keep the left mouse button depressed and slide the mouse pointer down until
“Fuel Table” is highlighted. Release the left mouse button. The screen below will open.
33. Fuel Table
Note: In some
cases, the ECU shipped with your system will come pre-configured with a table that
will closely match your engine configuration.
The Fuel table uses Volumetric Efficiency (VE) values in each of the 256 cells in the table.
Volumetric Efficiency is the measure for how efficient the engine is operating at a given engine speed
and load combination. The efficiency of the engine is nearly perfect, at a value of 100.
Volumetric Efficiency (VE) is highest at peak torque.
Note: If the fuel map VE values, around peak torque, are above 125, there is a good chance the
injector flow rates, inputted into the Operating Configuration/ Fueling Parameters table, are too low.
The opposite can also be true. If the VE values near peak torque are below 80, there is a good chance
the injector flow rates, inputted into the Operating Configuration/Fueling Parameters table, are too
high.
Fuel Table
Icon
Fuel table drop down
screen accessed from
the Main Tool Ba
r
The ellipse will move
throughout the Fuel table
relative to the current RPM
& Load “operating point”
- BigComm Software 1
- User Instruction Manual 1
- Table of Contents 2
- Table of Contents Continued 3
- 1. Introduction 3
- Firewall grommet 7
- MUST BOTH be 8
- The vehicle 9
- BigStuff3 Pro SEFI System 10
- Fuel Pump 13
- Ignition Systems Setup 18
- Connector Clip 19
- Connector Pin-out Identifier 23
- Minimum 26
- TPS, RPM 26
- Parameters 26
- Using the Brake Pedal Switch 27
- Connector) 32
- 7. ECU Installation 34
- 8. BigComm Software Overview 35
- 11. Using the Tool Bar 41
- BigComm 42
- 13. BigComm Main Menu Screen 45
- “Enter” 45
- For setup detail go to 49
- Coil-on-Plug (COP) 49
- Crank_Trigger_Configur 49
- TPS Signal in the Dash 50
- s)] to be used 51
- seconds) 51
- Ford Mod Motors: 329 52
- 20. Load vs. RPM 56
- Dwell Time Table 57
- 21. Firing Order 59
- 22. Injector Opening Time 59
- 23. Injector Phase Angle 60
- 25. Air Fuel Ratio Table 62
- Cell Values Selected in a Row 63
- 14 14 13.5 13.8 63
- 14 13.9 13.8 13.8 63
- 26. Positive 02 Correction 66
- 27. Negative 02 Correction 67
- 30. SPARK (F4 – “Quick Key”) 69
- 31. Spark Table 69
- 32. FUEL (F3 – “Quick Key”) 72
- 33. Fuel Table 73
- Enter” to save the change 74
- 34. STARTING 76
- Cranking 77
- After Start Delay 77
- After Start Decay 77
- 36. AfterStart Delay 78
- 37. AfterStart Correction 78
- 38. AfterStart Decay 79
- 39. Idle 80
- 40. Throttle Follower 80
- 41. Desired Idle RPM 81
- 42. Idle Spark 81
- 43. IAC Start Position 82
- 44. IAC Gain Terms 83
- 45. Warm Up 86
- 48. TRANSIENT FUEL 88
- 51. MAP AE Decay Rate 90
- 52. MAP AE Inc Rate 91
- 53. Run Time Correction 91
- 54. dMAP Parameters 92
- 55. Accel Pump Shot 94
- 56. AE Position Correction 94
- 57. Individual Cylinder 95
- 61. Boost Parameters 98
- 62. Boost PWM 99
- 63. Boost Staged 100
- Switched 101
- “Enter” to save the change 102
- 65. Dash 103
- 66. Configure Dash 103
- 67. Save a Dash 106
- 68. Load From File 107
- 69. Save to File 108
- 71. Logging (External) 109
- 72. Configure Log 110
- 74. View Log from File 111
- Feature 115
- 77. Configure Replay 116
- 78. Upload Replay 117
- 79. View Replay from File 118
- SR2 with ETM 119
- NTK WBO2 for methanol 119
- CAN EGT 119
- Blue Ellipse represents the 122
- Set Default Calibration 125
- 83. Load a Calibration 126
- 84. Acronym Definition 127
- 85. Control Keys 127
- 86. Function or “Quick Keys” 128
Powiązane produkty i podręczniki dla Do samochodu Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI System Hardware & BigC
Do samochodu Precision-turbo-and-engine BigStuff3 GEN3 PRO SEFI (LS1) System Hardware & Instrukcja Użytkownika
(122 strony)
(122 strony)
Do samochodu Precision-turbo-and-engine NLR AMS-500 Boost Controller Instrukcja Użytkownika
(8 strony)
(8 strony)
Do samochodu Precision-turbo-and-engine NLR AMS-1000 Boost Controller Instrukcja Użytkownika
(25 strony)
(25 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji